Leuze electronic DCR 248i Скачать руководство пользователя | Manualshive

Страница: 29 / 115

background image

Mounting

Leuze electronic

DCR 248i

29

6.2.3

Mounting with the BT 320M mounting bracket

Mounting with a BT 320M mounting bracket is intended for wall mounting. For ordering information, see
chapter 16.5 "Other accessories".

Ä

Mount the mounting bracket on the system side with M4 fastening screws (included in delivery con-
tents).

Ä

Mount the device to the mounting bracket with M4 fastening screws.

ð

Max. tightening torque of the fastening screws: 1.4 Nm

ð

Location and thread depth of the mounting thread: see chapter 15.3 "Dimensioned drawings"

6.2.4

Mounting with the BTU 320M-D12-RL70 mounting bracket

Mounting using a BTU 320M-D12-RL70 mounting bracket is intended for 12 mm rod mounting in combina-
tion with the RL-70/40r-003-M12 ring light. For ordering information, see chapter 16.5 "Other accessories".

Ä

Mount the ring light to the mounting bracket with M4 fastening screws.

Ä

Mount the device to the mounting bracket with M4 fastening screws.

ð

Max. tightening torque of the fastening screws: 1.4 Nm

ð

Location and thread depth of the mounting thread: see chapter 15.3 "Dimensioned drawings"

Ä

Mount the mounting bracket on the rod with the clamp profile (system-side).

6.3

Replace housing hood

In individual cases, you can exchange the housing hood of the code reader, e.g., if the protective screen is
scratched or if changed operating conditions necessitate a housing hood with polarization filter. For order-
ing information, see chapter 16.3 "Optical accessories".

NOTICE

Only replace the housing hood while the device is in a de-energized state!

Only replace the housing hood if no voltage is being applied to the device.

Ä

Disconnect the device from the voltage supply before replacing the device hood.

NOTICE

Check the seal before mounting!

Ä

Check the seal on the base of the code reader housing for cleanliness before mounting the
new housing hood.

NOTICE

Clean the new housing hood before mounting!

Ä

Clean the new housing hood with a soft cloth before mounting.

Ä

Loosen the four fastening screws of the housing hood.

Ä

First tip the housing hood downward and away from the housing base.

Ä

Then lift the housing hood up and off of the housing base.

Ä

Then mount the new housing hood in the reverse order. The tightening torque of the fastening screws
is 0.25 Nm.

«
...
27
28
29
30
31
...
»

Содержание DCR 248i




















































































































Отзывы:

Нет отзывов

Похожие инструкции для DCR 248i

Cubit IS6520 Series

Бренд: Metrologic Страницы: 48

AquaTronics MS-850

Бренд: ASA Electronics Страницы: 5

PowerScan Area Imager

Бренд: Datalogic Страницы: 44

Бренд: Boss Audio Systems Страницы: 48

Бренд: Cognex Страницы: 35

Бренд: Avery Dennison Страницы: 103

Бренд: Denver Страницы: 10

Бренд: DAQ system Страницы: 21

Stratus SV3TK1C

Бренд: Sirius Satellite Radio Страницы: 48

Бренд: Encore Страницы: 3

Бренд: Magtek Страницы: 2

Бренд: Wasp Страницы: 5

Бренд: Tatu Marchesan Страницы: 68

Бренд: VDO Страницы: 2

Linea Pro 7 UHF

Бренд: Infinite Peripherals Страницы: 15

Бренд: Infinite Peripherals Страницы: 4

Бренд: Boss Audio Systems Страницы: 8

Бренд: Sony Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды