Leuze electronic AMS 307i 120 Скачать руководство пользователя страница 45

Страница: 45 / 72

Display and control panel AMS 307i

AMS 307

Leuze electronic

Green continuous light

BUS LED green

- SSI interface is activated

Flashing green

BUS LED flashes green

- SSI interface is being initialized

8.2.3

Control buttons

Navigate upward/laterally.

Down

Navigate downward/laterally.

ESC

Exit menu item.

ENTER

Confirm/enter value, change menu levels.

Navigating within the menus

The menus within a level are selected with the up/down buttons

The selected menu item is activated with the enter button

Press the ESC button

to move up one menu level.

When one of the buttons is actuated, the display illumination is activated for 10min.

Setting values

If input of a value is possible, the display looks like this:

Use the

and

buttons to set the desired value. An accidental, incorrect entry can

be corrected by selecting

<-|

and then pressing

Then use the

buttons

to select

Save

and save the set value by pressing

ESC

100

<-|0123456789 save

Default ----------------- unit

126

| |

elete character

Enter digit

Save

Содержание AMS 307i 120









































































Результаты поиска

Содержание AMS 307i 120

Отзывы:

Leuze electronic AMS 307i 120, Руководство по эксплуатации, Страница: 45 / 72

Результаты поиска

Содержание AMS 307i 120

Отзывы: