manualshive.com logo in svg

Leuze electronic 50038948, Оригинальная инструкция по эксплуатации

Поделиться
Скачать
Leuze electronic 50038948 Скачать руководство пользователя страница 37

Installation

Leuze electronic

BCL 8

35

TN

T 3

5/7-

24V

6.3

Connection

6.3.1

Connecting the BCL 8

BCL 8 pin assignment

Figure 6.3: BCL 8 pin assignment

Connection description

Table 6.1:

Wiring description BCL 8

 

ATTENTION!

The BCL 8 bar code reader is completely sealed and cannot be opened. 

Do not try to open the device under any circumstances, as this avoids both degree of

protection IP 67 and the warranty.

Before connecting the device, be sure that the supply voltage agrees with the value 

printed on the name plate.

Connection of the device and maintenance work while under voltage must only be car

-

ried out by a qualified electrician. 

The power supply unit for the generation of the supply voltage for the BCL 8 and the 

corresponding connection units must have a secure electrical insulation according to 

IEC 60742 (PELV). For UL applications: only for use in class 2 circuits according to 

NEC.

Take care to connect the protective conductor correctly to the housing screen. Fault-

free operation is only guaranteed when the device is properly earthed.

If faults cannot be cleared, the device should be switched off and protected against 

accidental use.

Pin 1

+5V DC

Operating voltage 5VDC

Pin 2

RS 232 TxD

TxD signal line of the RS232 interface

Pin 3

GND

Operating voltage 0VDC / reference ground

Pin 4

RS 232 RxD

RxD signal line of the RS232 interface

Pin 5

SW IN/OUT

Switching input or switching output

Top view of the BCL 8 connector

UM_BCL8_de_50040581.book  Seite 35  Montag, 24. Februar 2020  9:53 09

Содержание 50038948











































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды