Leonton GINJ-0201-AT-24 Series Скачать руководство пользователя страница 17 | Manualshive

Страница: 17 / 17

Leonton GINJ-0201-AT-24 Series Скачать руководство пользователя страница 17

11

Trouble Shooting



Verify you have the right power cord or adapter. Never use a power supply or adapter with a
non-compliant DC output voltage or it will burn the equipment.



Select the proper UTP or STP cable in order to construct the network. Use an unshielded
twisted-pair (UTP) or shield twisted-pair (STP) cable for RJ-45 connections: 100Ω Category 5e

for 10M/100M/1000Mbps. Also be sure that the length of any twisted-pair connection does

not exceed 100 meters (328 feet).

NOTE: The total length from the device A through the Injector to the device B must not exceed

100 meters



Diagnosing LED Indicators: To assist in identifying problems, the injector can be easily
monitored with the LED indicators which help to identity if any problems exist.



Please refer to the LED Indicators section for LED light indication.



If the power indicator LED does not turn on when the power cord is plugged in, the user may
have a problem with the power cord. Check for loose power connections, power losses or

surges at the power outlet.



Please contact LEONTON for technical support service, if the problem still cannot be

resolved.

«
...
15
16
17

Содержание GINJ-0201-AT-24 Series


















Отзывы:

Нет отзывов