SAFETY INSTRUCTIONS
Please read carefully and follow this OA EXTRA series UPS guide.
Important :
Please keep this user's guide for reference in order to use the UPS properly
and safety. This user's guide contains instructions for installation, operation
and specifications.
For product safety, please check this product annually by our service qualified per-
sonnel or if there are any symptoms of problems which are not mentioned in this guide or
an queries, please contact your LEONICS local distributors,LEONICS Service Center, send
e-mail to [email protected] or visit www.leonics.com.
Caution
Risk of electric shock, DO NOT remove cover. No user serviceable part
inside, please refer servicing to qualified service personnel.
1.1 Electrical Safety
1.1.1 Do not work alone where there are electrically hazardous conditions.
1.1.2 Contact with live conductors will cause burns and dangerous electric shock.
1.1.3 Only qualified electricians allow to install and wiring this unit and the system.
1.1.4 Periodically check your cable, terminal and power source to make sure that
they are in good condition.
1.1.5 To reduce risk from electric shock if you can not find the electrical ground
(
) of the building, unplug the UPS from the AC source before plug in your
load at the rear side of the UPS. Then, plug in the UPS to AC source.
1.1.6 Do not touch any metal parts or any electrical connection when UPS is operating.
1.1.7 Use ONLY one hand when plugging and unpluging the load in order to avoid
electric shock from touching two surfaces with different potential.
1.1.8 It is recommended to connect the UPS to a three wire AC source (two live wires
and ground) which connects to a protected circuit such as employs a fuse or
circuit breaker.
1.2 CAUTION ! Safety guide for installation and operation
1.2.1 Before installing or using this unit, read all instructions, caution markings on
the UPS and all connected load, and all sections of this user guide.
1.2.2 Install this unit in a temperature and humidity controlled indoor area with
adequate air flow and away from chemical particles or flammable substances .
Avoid installing the unit near radio transmission station, heat dissipation equip-
ment and direct sunlight.
1.2.3 This unit has ventilation grills. Ensure that sufficient ventilation is provided.
DO NOT block the ventilation grills.
1.2.4 Use insulated tools to reduce your risk of electric shock.
1.2.5 Remove all jewelry or other metal objects such as rings, necklace, bracelets
and watches when installing this product.
1.2.6 Properly wiring the cables as shown in the wiring diagram.
1.2.7 Before connecting the communication interface signal cable, Turn off the UPS
by pressing the front panel button until the Utility Line OK/Fail ( ) and
Overload Alarm ( ) lamps are lit at the same time and the alarm sounds
once. Then, release the button.
1.2.8 Turn on the UPS before turn on the load to prevent surge from the loads.
1.2.9 DO NOT connect utility power to the UPS OUTPUT. This may cause the UPS
damaged.
1.2.10When heavy rain, avoid using electronic equipments including UPS to prevent
it from lightning.
1.2.11Use soft cloth to clean the UPS when it is turned OFF. DO NOT clean it with
solvent.
1.2.12DO NOT use the UPS with life recovery instruments. The failure of UPS may
cause life recovery instruments failure or effect to their performance or effect
to the safety system of those instruments.
1.3 Warning ! Battery Safety
1.3.1 Although the UPS is not connected to any power source, its outlets may be
energized because it has a battery inside.
1.3.2 The UPS has hazardous voltages inside, do not disassemble any parts of UPS
except for the battery. Users are allowed to replace battery by turning off power
switch at the rear side of the UPS, then unplug the AC input cable. Users are not
allowed to repair, recondition or disassemble the UPS. This must be done by
Leonics qualified technicians only.
This product contains sealed lead acid battery and must be recycled
properly. For recycling please return it to a LEONICS local distributor or
LEONICS Service Center or contact your local recycling center for proper
disposal information.
1.3.3 Do not dispose of batteries in a fire. They may be exploded.
1.3.4 Do not disassemble batteries. They contains poisonous electrolyte which is
harmful to your skin and eyes.
1.3.5 Replace batteries with the same type and rating and follow the proper battery
replacement procedure.
1.3.6 When replacing a battery, use tools with insulated handles and remove any
watch, rings or other metal objects that you wear in order to avoid electric shock.
1.3.7 If user has to keep the UPS or does not use if for long time, recharge the battery
every 3 months in order to preserve the battery. To recharge the battery,
connect it to the AC utility and turn on the UPS for 8 hours.
SPECIFICATION
*PC = Pentium 4 , 1.8GHz with 15” monitor respectively., **Printer = Bubble jet or Dot matrix printer.
Continuous product development is our commitment. In that manner, the above specifications may be changed without prior notice.
MODEL
OA EXTRA 525 OA EXTRA 750 OA EXTRA 1000 OA EXTRA 1500
CAPACITY
Power factor = 0.6
525 VA (315W)
750 VA (450W)
1000 VA (600W)
1500 VA (900 W)
SYSTEM
UPS system
Digital Line Interactive UPS
Control system
Microprocessor 8 bit
Stabilizer function
Buck / Boost
LOAD
The number of PC*
1 set + printer** 2 sets + printer**
3 sets + printer**
4 set + printer**
APPLICATION
INPUT
Input Voltage
220 Vac ± 25% (230 Vac option)
Nominal Input (single phase)
220 Vac (230Vac option)
Frequency
50Hz ± 6% (60Hz ± 6%) (auto sensing) (50Hz ± 10% option)
OUTPUT
Voltage stabilizer mode (sine wave)
220 Vac ± 10% (230 Vac option)
Voltage backup mode for 1 PC
220 Vac ± 5% (230 Vac option)
(modify sine wave)
Frequency (backup mode)
50Hz ± 0.1% (60Hz ± 0.1%) (auto sensing)
PROTECTION
Transfer time
5 ms. (in-phase transfer)
Output short circuit
Auto cut - off with audio & visual alarm
Overload protection
Fuse protection
Circuit breaker
Surge energy dissipation
STD. UL1449 : 160 Joules (IC = 6500A)
Power dissipation
1,600,000 W within 100 microsec.
Acoustic noise
Less than 40 dBA at 1 metre
BATTERY
Type
Sealed lead acid (maintenance free)
Capacity
12 V 7 Ah
12 V High Rate
2 x 12 V 7 Ah
2 x 12 V High Rate
(12 V High Rate option)
Backup time
15 - 40 min. (depend on load)
Continuous recharging time to 80%
3 - 8 hours
OUTPUT OUTLET
Number of backup outlet
3
6
Number of surge protection outlet
1
1
FEATURE
Power Watcher
yes
Noload shutdown option switch
yes
Backup test switch
yes
DC start
yes
Communication interface
Level communication (DB-9)
Easy-Mon software
UPS status, Backup time remaining, Schedule shutdown computer and UPS
Restart voltage checking system
yes
Surge protection for telephone line
yes
Surge protection for LAN line
option
Surge protection for laser printer
yes
Operating with generator
yes
User replaceable battery
yes
ENVIRONMENT
Temperature
0 - 45°C
Humidity
0 - 95% (non - condensing)
PHYSICAL
W x H x D (cm.)
10 x 16.5 x 30
10 x 16.5 x 30
12.5 x 21 x 36
12.5 x 21x 36
DIMENSIONS
WEIGHT
Approximate in kg.
8
8.5
14
17
CONFORMANCE
Design regulation
EN 50091-2, EN 50022 (B), EN 61000-4-2, (4), (6), IP 21
