Lenze PROFINET 9400 Скачать руководство пользователя страница 80

Страница: 80 / 119

Diagnostics

12.1

LED status displays

Lenze · E94AYCER communication module (PROFINET®) · Communication Manual · DMS 11.0 EN · 04/2016 · TD17

_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _

12.1.1

Module status displays

Module status displays are indicated by the LEDs

, and

E94YCET001E

Pos.

Colour

Status

Description

Green

The communication module is supplied with voltage and is

connected to the standard device.

Blinking

The communication module is supplied with voltage, but is not

connected to the standard device. (Standard device is switched off,

in the initialisation phase, or not available.)

Red

An error has occurred in the communication module.

Blinking

The "Node blinking test" PROFINET function is activated by the I/O

controller.

The blinking LED serves to identify/localise accessible I/O devices.

Red

The communication module is not accepted by the basic device or

the basic device is not active (see notes in the documentation

relating to the basic device.)

200 ms

Содержание PROFINET 9400
























































































































Результаты поиска

Содержание PROFINET 9400

Отзывы:

Похожие инструкции для PROFINET 9400

Бренды по названию

Популярные бренды

Lenze PROFINET 9400, Руководство по связи

Результаты поиска

Содержание PROFINET 9400

Отзывы:

Похожие инструкции для PROFINET 9400

Бренды по названию

Популярные бренды