Lenze PROFINET 9400 Скачать руководство пользователя страница 37

Страница: 37 / 119

Lenze · E94AYCER communication module (PROFINET®) · Communication Manual · DMS 11.0 EN · 04/2016 · TD17

Commissioning

6.4

Setting the IP configuration

_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _

6.4

Setting the IP configuration

The IP configuration is required for addressing the Servo Drive 9400 in the PROFINET network. For

this purpose, an IP address, subnet mask and gateway address have to be allocated.
If no PROFINET network or IO controller is available yet, you can allocate the IP address, subnet

mask, and gateway address for the communication module by using the following options:

•

Setting via the PROFINET configurator of the »Engineer«

(



38)

•

Setting via codes in the »Engineer«

(



40)

•

Setting via Siemens »STEP7« (»HW Konfig«)

(



43)

•

Setting via the Siemens »Primary Setup Tool«

(



47)



Note!

• If the IP parameters are assigned by the IO Controller via the PROFINET, the PROFINET

configurator of the »Engineer«, Siemens »STEP7« or the Siemens »Primary Setup

Tool«, the changes become effective immediately and are saved with mains failure

protection.

• The assignment of invalid combinations of the IP address, subnet mask, and gateway

address can have the consequence that no connection to PROFINET can be

established.

• In case of impermissible settings, the red LED

(

Fieldbus status displays

(



81)

) is

blinking and the error message

PROFINET: Invalid IP parameters [0x00c86533]

(



89)

is output.

Содержание PROFINET 9400
























































































































Результаты поиска

Содержание PROFINET 9400

Отзывы:

Похожие инструкции для PROFINET 9400

Бренды по названию

Популярные бренды

Lenze PROFINET 9400, Руководство по связи

Результаты поиска

Содержание PROFINET 9400

Отзывы:

Похожие инструкции для PROFINET 9400

Бренды по названию

Популярные бренды