Lenze POWERLINK E84DGDV Series Скачать руководство пользователя страница 43

Страница: 43 / 70

Lenze · Decentralised frequency inverter 8400 motec (POWERLINK Option) · EDS84DMOTPL EN 1.0 - 11/2018

Error messages

Possible causes and remedies

_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _

EPL: Watchdog reset [0x01bc6011]

EPL: Software error [0x01bc6100]

EPL: Fatal software error [0x01bc6101]

EPL: PDO Mapping invalid [0x01bc6110]

EPL: Invalid parameter set [0x01bc641f]

EPL: Factory settings loaded [0x01bc6420]

Response

(Lenze setting printed in bold)

Setting:

not possible



No reaction



System fault



Fault



Trouble



Quick stop by trouble



WarningLocked



Warning



Information

Cause

Remedy

Communication unit is defective.

Send Communication Unit with error description to

Lenze.

Response

(Lenze setting printed in bold)

Setting:

not possible



No reaction



System fault



Fault



Trouble



Quick stop by trouble



WarningLocked



Warning



Information

Cause

Remedy

Communication unit is defective.

Send Communication Unit with error description to

Lenze.

Response

(Lenze setting printed in bold)

Setting:

not possible



No reaction



System fault



Fault



Trouble



Quick stop by trouble



WarningLocked



Warning



Information

Cause

Remedy

Communication unit is defective.

Send Communication Unit with error description to

Lenze.

Response

(Lenze setting printed in bold)

Setting:

not possible



No reaction



System fault



Fault



Trouble



Quick stop by trouble



WarningLocked



Warning



Information

Cause

Remedy

Invalid mapping configuration.

Correct the mapping configuration.

Response

(Lenze setting printed in bold)

Setting:

not possible



No reaction



System fault



Fault



Trouble



Quick stop by trouble



WarningLocked



Warning



Information

Cause

Remedy

No active parameter set could be loaded.

Download application again (including module).

Response

(Lenze setting printed in bold)

Setting:

not possible



No reaction



System fault



Fault



Trouble



Quick stop by trouble



WarningLocked



Warning



Information

Cause

Remedy

Access to parameter set in memory module via standard

device was not successful.

Download application again (including module).

Содержание POWERLINK E84DGDV Series







































































Результаты поиска

Содержание POWERLINK E84DGDV Series

Отзывы:

Похожие инструкции для POWERLINK E84DGDV Series

Бренды по названию

Популярные бренды

Lenze POWERLINK E84DGDV Series, Руководство по связи

Результаты поиска

Содержание POWERLINK E84DGDV Series

Отзывы:

Похожие инструкции для POWERLINK E84DGDV Series

Бренды по названию

Популярные бренды