Lenze PositionServo 940 Скачать руководство пользователя страница 25 | Manualshive

Страница: 25 / 68

background image

S94P01B

23

5.2.2 Digital outputs

There are a total of ﬁve digital outputs (“OUT1” - “OUT4” and “RDY”) available on
the PositionServo 940 drive. These outputs are accessible from the P3 connector.
Outputs are open collector type that are fully isolated from the rest of the drive circuits.
See the following ﬁgure for the electrical diagram. These outputs can be either used
via the drives internal User Program or they can be conﬁgured as Special Purpose
outputs. When used as Special Purpose, each output (OUT1-OUT4) can be assigned
to one of the following functions:

• Not assigned
• Zero speed
• In-speed window
• Current limit
• Run-time fault
• Ready
• Brake (motor brake release)

Please note that if you assign an output as a Special Purpose Output then that output
can not be utilized by the User Program. The “RDY” Output has a ﬁxed function,
“ENABLE”, which will become active when the drive is enabled and the output power
transistors becomes energized.

Digital outputs electrical characteristics

Circuit type

Isolated Open Collector

Digital outputs load capability

100mA

Digital outputs Collector-Emitter max voltage

30V

��

��

��

��

��

��

��

��

S907

Digital outputs circuit

«
...
23
24
25
26
27
...
»

Содержание PositionServo 940





































































Отзывы:

Нет отзывов

Похожие инструкции для PositionServo 940

Бренд: D+H Страницы: 8

Бренд: Panasonic Страницы: 14

Бренд: Panasonic Страницы: 15

Бренд: Panasonic Страницы: 15

Бренд: Panasonic Страницы: 15

Бренд: Panasonic Страницы: 19

Бренд: Panasonic Страницы: 18

Бренд: Panasonic Страницы: 26

Бренд: Panasonic Страницы: 40

VW-BN1 - DVD-RW / DVD-RAM Drive

Бренд: Panasonic Страницы: 104

Бренд: Panasonic Страницы: 160

Бренд: Panasonic Страницы: 160

Бренд: Panasonic Страницы: 59

Бренд: Panasonic Страницы: 156

Бренд: Cole Parmer Страницы: 8

PumpSmart PS200

Бренд: ITT Industries Страницы: 159

Бренд: Iomega Страницы: 24

Бренд: Grundig Страницы: 20

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды