Lenze PositionServo 940 Скачать руководство пользователя страница 13 | Manualshive

Страница: 13 / 68

background image

S94P01B

11

4 Installation

Perform the minimum system connection. Please refer to section 8.1 for minimum
connection requirements. Observe the rules and warnings below carefully:

DANGER!

Hazard of electrical shock! Circuit potentials are up to 480 VAC above
earth ground. Avoid direct contact with the printed circuit board or
with circuit elements to prevent the risk of serious injury or fatality.
Disconnect incoming power and wait 60 seconds before servicing
drive. Capacitors retain charge after power is removed.

STOP!

• The PositionServo 940 must be mounted vertically for safe operation

and enough cooling air circulation.

• Printed circuit board components are sensitive to electrostatic

ﬁelds. Avoid contact with the printed circuit board directly. Hold the
PositionServo 940 by it’s case only.

• Protect the drive from dirt, ﬁlings, airborne particles, moisture, and

accidental contact. Provide sufﬁcient room for access to the terminal
block.

• Mount the drive away from any and all heat sources. Operate within

the speciﬁed ambient operating temperature range. Additional
cooling with an external fan may be recommended in certain
applications.

• Avoid excessive vibration to prevent intermittent connections

• DO NOT connect incoming (mains) power to the output motor

terminals (U, V, W)! Severe damage to the drive will result.

• Do not disconnect any of the motor leads from the PositionServo

940 drive unless (mains) power is removed. Opening any one motor
lead may cause failure.

• Control Terminals provide basic isolation (insulation per EN61800-

5-1). Protection against contact can only be ensured by additional
measures, e.g., supplemental insulation.

WARNING!

For compliance with EN61800-5-1, the following warning applies.

This product can cause a d.c. current in the protective earthing
conductor. Where a residual current-operated protective (RCD) or
monitoring (RCM) device is used for protection in case of direct or
indirect contact, only an RCD or RCM of Type B is allowed on the
supply side of this product.

«
...
11
12
13
14
15
...
»

Содержание PositionServo 940





































































Отзывы:

Нет отзывов

Похожие инструкции для PositionServo 940

Бренд: GFA Страницы: 21

Бренд: Baldor Страницы: 32

MRZJW3- SETUP161E

Бренд: Mitsubishi Electric Страницы: 29

Бренд: Mitsubishi Electric Страницы: 72

Бренд: Mitsubishi Electric Страницы: 80

Melservo-Jet HG-KNS Series

Бренд: Mitsubishi Electric Страницы: 108

Melservo-J4 MR-J4-DU*B4-RJ100 Series

Бренд: Mitsubishi Electric Страницы: 86

MELSERVO MR-HP30KA

Бренд: Mitsubishi Electric Страницы: 115

Бренд: Mitsubishi Electric Страницы: 156

Бренд: Mitsubishi Electric Страницы: 104

Melservo-H Series

Бренд: Mitsubishi Electric Страницы: 92

Бренд: Mitsubishi Electric Страницы: 284

MR-J2S-*A series

Бренд: Mitsubishi Electric Страницы: 344

Бренд: Mitsubishi Electric Страницы: 392

MR-J4-100B(-RJ)

Бренд: Mitsubishi Electric Страницы: 706

Бренд: Mitsubishi Electric Страницы: 323

MR-J2S-11K Series

Бренд: Mitsubishi Electric Страницы: 2

ThinkPad 73P3279

Бренд: IBM Страницы: 54

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды