manualshive.com logo in svg

Lenze L-force Communication ModemCAN EMF2181IB, Руководство по связи, Страница: 80 / 83

Поделиться
Скачать
Lenze L-force Communication ModemCAN EMF2181IB Скачать руководство пользователя страница 80

Index

11

     

l

80

EDSMF2181IB  EN  3.0

11

Index

A

Application, as directed,  6

Application as directed,  6

Application range,  14

AT commands,  70

B

Baud rate, system bus (CAN). 

Siehe

 baud rate

Bus cable length,  25

C

C0002: Device commands,  58

C0099: Software version,  58

C0150: Status word,  58

C0200: Software ID,  59

C0350: CAN node address,  48

C0351: CAN baud rate,  49

C0351: Set baud rate,  49

C0358: Reset node,  50

C0359: Diagnostics of the bus status,  50

C0360: Diagnostics of the telegram counter,  51

C0361: Diagnostics bus load,  52

C1200: Parameter data channel operating mode,  52

C1201: Communication timeout (CAN),  53

C1202: Time limit for node search,  53

C1203: Repeat tests,  53

C1204: Password,  60

C1205: Callback phone number,  61

C1206: Modem initialisation,  62

C1207: Switch−over internal / external modem,  62

C1208: Country code,  63

C1209:Read out baud rate,  54

C1213: Fieldbus connection,  59

C1215: Automatic baud rate detection,  54

C1219: Activation of CAN device monitoring,  54

C1223: user name,  63

C1225: baud rate of the external modem,  64

C1226: modem reset,  64

C1227: Delay time for search telegrams,  55

Cable cross−section,  25

Cable specification,  24

Call control commands,  73

CAN bus connection,  24

CANopen objects,  45

CANopen objects implemented,  47

CANopen parameter channels,  42

CANopen RUN LED and ERROR LED,  65

CE conformity,  6

CE−typical drive system,  20

Code numbers, Access via the communication module,  42

Code numbers / index, Conversion,  42

Commands for the DEE modem,  72

Commissioning,  31

− Initial switch−on,  38

Commissioning with the system bus configurator,  32

Communication via CAN,  21

Communication via the diagnostic interface (9400),  22

Configuring the communication module,  35

Conformity,  6,  15

Connection for an external modem,  28

Connection for the CAN bus,  24

Connections,  11

Controls,  11

D

Data compression commands,  78

Data transfer,  41

Data transfer via modem,  44

Data transfer via the diagnostic interface,  43

Definition of notes used,  10

Description of the CANopen objects implemented,  56

Description of the codes relevant for CAN,  48

Description of the codes relevant for the modem,  60

Description of the general codes,  58

Device protection,  9,  18

Device type,  56

Diagnostic interface,  30

Displays,  11

Disposal,  7

Содержание L-force Communication ModemCAN EMF2181IB




















































































Отзывы:

Нет отзывов