Lenze L-force Communication ModemCAN EMF2181IB Скачать руководство пользователя страница 27

Страница: 27 / 83

Installation

Electrical installation

Connection for the CAN bus

EDSMF2181IB EN 3.0

Check repeater application

Given:

Baud rate:

125 kbit/s

Cable cross−section:

0.5 mm

Number of nodes:

Cable length:

450 m

Test sequence

Cable length

See

1. Total cable length at 125 kbit/s:

630 m

Tab. 5−1

2. Segment cable length for 28 nodes and a cable cross−section of

0.5 mm

360 m

Tab. 5−2

3. Comparison: The value under point 2 is smaller than the required cable length of 450 m.

Conclusion

It is not possible to use a cable length of 450 m without installing a repeater.

After 360 m (point 2) a repeater must be installed.

Result

The Lenze repeater, type 2176 (cable reduction: 30 m), is used.

Calculation of the max. cable length:
First segment: 360 m
Second segment: 360 m (according to Tab. 5−1)

minus

30 m (cable reduction when a repeater is used)

Max. possible cable length with repeater: 690 m.

Now the required cable length is possible.

)

Note!

The use of a further repeater is recommended as a

Service interface

Advantage:

Trouble−free connecting during ongoing bus operation is

possible.

Calibration interface

Advantage:

Calibration/programming unit remains electrically isolated.

Содержание L-force Communication ModemCAN EMF2181IB




















































































Результаты поиска

Содержание L-force Communication ModemCAN EMF2181IB

Отзывы:

Lenze L-force Communication ModemCAN EMF2181IB, Руководство по связи, Страница: 27 / 83

Результаты поиска

Содержание L-force Communication ModemCAN EMF2181IB

Отзывы: