Lenze I/O system 1000 Скачать руководство пользователя страница 324 | Manualshive

Страница: 324 / 583

Lenze I/O system 1000 Скачать руководство пользователя страница 324

Lenze · I/O system 1000 · Reference Manual · DMS 5.0 EN · 09/2016 · TD17

324

7

EtherCAT communication

7.1

About EtherCAT

_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _

7.1.1

EtherCAT frame

EtherCAT frames have the following structure:

Ethernet header

The Ethernet header contains the following information:

• Target address of the EtherCAT frame (destination)
• Source address of the EtherCAT frame (source)
• Type of the EtherCAT frame (EtherType)

Ethernet data

The Ethernet data contain the following information:

• Length of the datagrams within the EtherCAT frame (length)
• One reserved bit
• Type of the datagrams within the EtherCAT frame (type)
• Datagrams

FCS

• Checksum of the EtherCAT frame

Ethernet header

Ethernet data

FCS

48 bits

48 bits

16 bits

11 bits

1 bit

4 bits

48 ... 1498 bytes

32 bits

Destination

Source

EtherType

header

Datagrams

Length

Reserved

Type

«
...
322
323
324
325
326
...
»

Содержание I/O system 1000








































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов