Lenze I/O system 1000 Скачать руководство пользователя страница 27

Страница: 27 / 583

Product description

2.6

Counter modules EPM-S600 ... EPM-S603 – control and status words

Lenze · I/O system 1000 · Reference Manual · DMS 5.0 EN · 09/2016 · TD17

_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _

2.6

Counter modules EPM-S600 ... EPM-S603 – control and status words

2.6.1

Status word EPM-S600

* The bits are set until reset with RES_SET (bit 6 control word)

Bit

Name

Function

STS_SYNC

Reset was active

STS_CTRL_DO

Is set if the digital output is enabled

STS_SW-GATE

Software gate status (set if SW gate active)

STS_RST

Status of the reset input

STS_STRT

Hardware gate status (set if HW gate active)

STS_GATE

Status of internal gate (set if internal gate active)

STS_DO

Status of digital counter output (DO)

STS_C_DN

Status set in the case of backward counter direction

STS_C_UP

Status set in the case of forward counter direction

STS_CMP*

Status of comparator is set if the comparison condition is met.

If the comparison is deactivated, (counter mode byte 1 = 0b000), the bit has

no function.

STS_END*

Status set if final value has been reached

STS_OFLW*

Status set in the case of an overflow

STS_UFLW*

Status set in the case of an underflow

STS_ZP*

Status set in the case of a zero crossing

STS_LTCH

Status of the latch input

Reserved

Содержание I/O system 1000








































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание I/O system 1000

Отзывы:

Lenze I/O system 1000, Справочное руководство, Страница: 27 / 583

Результаты поиска

Содержание I/O system 1000

Отзывы: