Lenze E84DGFCp Series Скачать руководство пользователя

Страница: 75 / 100

EDS84DMOTPBUS EN 3.0 - 11/2011

Communication manual 8400 motec PROFIBUS

Diagnostics

Diagnostic data

11.4

Diagnostic data



Present diagnostic data are signalled to the master by the PROFIBUS slave via an alarm

message.



Errors and warnings of the controller are sent to the master as extended diagnostic

messages.

General structure of diagnostic messages

Byte

Description

1 Bit 0: Station does not exist (set by the master).

Bit 1: Slave is not ready for data exchange.

Bit 2: Configuration data do not correspond.

Bit 3: Slave has extended diagnostic data.

Bit 4: Requested function is not supported by the slave.

Bit 5: Slave response is invalid (set by the master)

Bit 6: Incorrect parameter setting

Bit 7: Slave has been parameterised by another master (set by the master).

2 Bit 0: Slave must be parameterised again.

Bit 1: Static diagnostics

Bit 2: Permanently set to "1".

Bit 3: Watchdog active

Bit 4: Freeze command received.

Bit 5: Sync command received.

Bit 6: Reserved

Bit 7: Slave is deactivated (set by the master).

3 Bit 7: Diagnostics overflow - amount of diagnostic information present in the slave is too large to fit

into one telegram.

4 Bits 0 ... 7: Master address after parameterisation ("0xFF" without parameterisation)
5 Bits 0 ... 7: ID number (high byte)
6 Bits 0 ... 7: ID number (low byte)
7 Header

• The header contains the block length of the advanced diagnostics including the header byte.

• In this case, the value of the entry is "0x0A" (bytes 7 ... 16 = 10 bytes).

8 Status_Type

• The value of this entry is fixed. For the following bit assignment it is "0x81":

–Bit 7 = 1: "status"

–Bit 0 = 1: "status message"

–Value of all other bits = 0

9 Slot_Number

• The value of the slot number is "0x00".

10 Specifier

• An indicated error is entered in the specifier with the identification "0x1" (status coming).

• An eliminated error is entered in the specifier with the identification "0x02" (status going).

• If no errors are indicated, the entry in the specifier has the value "0x00" (no further

differentiation).

11 Reserved
12

13 ... 16 Error code of the controller

Содержание E84DGFCp Series





































































































Результаты поиска

Содержание E84DGFCp Series

Отзывы:

Похожие инструкции для E84DGFCp Series

Бренды по названию

Популярные бренды

Lenze E84DGFCp Series, Руководство по связи

Результаты поиска

Содержание E84DGFCp Series

Отзывы:

Похожие инструкции для E84DGFCp Series

Бренды по названию

Популярные бренды