Lenze E84DGFCp Series Скачать руководство пользователя

Страница: 49 / 100

EDS84DMOTPBUS EN 3.0 - 11/2011

Communication manual 8400 motec PROFIBUS

Parameter data transfer

DRIVECOM parameter data channel (DP-V0)

9.2.7

Telegram examples

9.2.7.1

Read request: Querying the heatsink temperature

The heatsink temperature of the controller is to be read.



Code to be read: C00061



Heatsink temperature: 43 °C

Byte 1: Service (request)



Request = 0t110001

bin

– Bit 0 ... 2 = 001

bin

for read request

– Bit 3 = 0 (reserved)
– Bit 4/5 = 01

bin

for 2-byte data length (only relevant for the response telegram)

– Bit 6 = handshake bit (t

≡

status is changed in the response telegram)

– Bit 7 = status bit (only relevant for the response telegram)

Byte 2: Subindex



Subindex = 0 because code C00061 does not contain any subindices.

Bytes 3 + 4: Index



Index = 24575 - code number = 24575 - 61 = 24514 = 0x5FC2
– Byte 3 (high byte) = 0x5F
– Byte 4 (low byte) = 0xC2

Bytes 5 ... 8: Data



The response telegram contains the value of code C00061:
– Data 3 + 4 = 43 [°C] x 1 (internal factor) = 43 = 0x002B

Result:



Request telegram from master to drive:



Response telegram from drive to master (for correct execution):

Byte 1

Byte 2

Byte 3

Byte 4

Byte 5

Byte 6

Byte 7

Byte 8

Service

Subindex

Index high byte

Index low byte

Data 4

Data 3

Data 2

Data 1

0x01

0x00

0x5F

0xC2

0x00

0t000001

bin

00000000

bin

01011111

bin

11000010

bin

00000000

bin

00000000

bin

00000000

bin

00000000

bin

Waiting for change of handshake bit 6 in service byte 1 of the response.

Byte 1

Byte 2

Byte 3

Byte 4

Byte 5

Byte 6

Byte 7

Byte 8

Service

Subindex

Index high byte

Index low byte

Data 4

Data 3

Data 2

Data 1

0x11

0x00

0x5F

0xC2

0x00

0x2B

0x00

0t010001

bin

00000000

bin

01011111

bin

11000010

bin

00000000

bin

00101011

bin

00000000

bin

00000000

bin

Содержание E84DGFCp Series





































































































Результаты поиска

Содержание E84DGFCp Series

Отзывы:

Похожие инструкции для E84DGFCp Series

Бренды по названию

Популярные бренды

Lenze E84DGFCp Series, Руководство по связи

Результаты поиска

Содержание E84DGFCp Series

Отзывы:

Похожие инструкции для E84DGFCp Series

Бренды по названию

Популярные бренды