manualshive.com logo in svg

Lenze E84DGFCp Series, Руководство по связи

Поделиться
Скачать
Lenze E84DGFCp Series Скачать руководство пользователя страница 18

Communication manual 8400 motec PROFIBUS

Technical data

General data and operating conditions

18

L

EDS84DMOTPBUS EN 3.0 - 11/2011

   

4

Technical data

4.1

General data and operating conditions

Hardware manual "Inverter Drives 8400 motec"

Here you will find the 

ambient conditions

 and information on the 

electromagnetic compatibility (EMC)

 that also apply to the communication unit.

Area

Values

Order designation

 • E84DGFCPxNx (PROFIBUS)

 • E84DGFCPxJx (PR Safety)

Communication profile

 • PROFIBUS DP-V0 (DRIVECOM)

 • PROFIBUS DP-V1 (PROFIdrive), from SW version 2.0

Standards / specifications

 • IEC 61158 / EN 50170

 • IEC 61784

Communication medium

RS485

Interface for communication

 • PROFIBUS input: M12 pins, 5-pole, B-coded

 • PROFIBUS output: M12 socket, 5-pole, B-coded

Max. cable length

1200 m (depending on the selected baud rate, the used cable type and 

hardware (repeaters))

Bus termination

Bus terminating resistors are required at the first and last PROFIBUS node 

(implemented in the connector of the bus cable)

Network topology

 • Line (without repeater)

 • Tree/line (with repeater)

Type of station

PROFIBUS slave

Number of slave stations

 • Max. 31 (without repeater)

 • Max. 125 (with repeater)

PNO identification number

0x0A89

Baud rate for cable type A (EN 50170) 9.6 kbps ... 12 Mbps (automatic detection)
External voltage supply

 • U = 24 V DC (20 V - 0 % ... 29 V + 0 %)

  • I

max

 = 400 mA

Conformities, approvals

 • CE

  • UR  /  cUR

Содержание E84DGFCp Series





































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды