manualshive.com logo in svg

Lenze E84DGFCp Series, Руководство по связи

Поделиться
Скачать
Lenze E84DGFCp Series Скачать руководство пользователя страница 12

Communication manual 8400 motec PROFIBUS

Safety instructions

General safety and application instructions

12

L

EDS84DMOTPBUS EN 3.0 - 11/2011

   

2

Safety instructions

2.1

General safety and application instructions

Lenze drive and automation components ...
– must only be used as directed.

Application as directed

 (

14)

– must never be commissioned in the event of visible damage.
– must never be technically modified.
– must never be commissioned before they have been completely mounted.
– must never be operated without the covers required.
– can - depending on their degree of protection - have live, movable or rotating parts 

during and after operation. Surfaces can be hot.

For Lenze drive components ...
– use only the accessories approved.
– use only original spare parts from the manufacturer.

Observe all specifications given in the attached and associated documentation.
– This is the precondition for safe and trouble-free operation and for achieving the 

product features specified.

Features and variants

 (

15)

– The procedural notes and circuit details described in this document are only 

proposals. It is up to the user to check whether they can be adapted to the particular 

applications. Lenze does not take any responsibility for the suitability of the 

procedures and circuit proposals described.

Note!

Always observe the specified safety measures to avoid severe injury to persons 

and damage to property!
Always keep this documentation to hand in the vicinity of the product during 

operation.

Danger!

If you disregard the following basic safety measures, this can cause severe injury 

to persons and damage to material assets.

Содержание E84DGFCp Series





































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды