Lenze E82ZAFIC010 Скачать руководство пользователя страница 32 | Manualshive

Страница: 32 / 71

Lenze E82ZAFIC010 Скачать руководство пользователя страница 32

Commissioning

Connecting the mains voltage

l

32

EDS82ZAFIC EN 2.0

6.6

Connecting the mains voltage

)

Note!

If the external voltage supply of the function module is used, switch it on as
well.

ƒ

The standard device is ready for operation approx. 1 s after switching on the supply
voltage.

ƒ

The controller inhibit is active.

ƒ

The green LED at the front of the function module is lit.

Protection against uncontrolled start−up

)

Note!

Establishing communication

For establishing communication via an externally supplied function module,
the standard device must be switched on as well.

ƒ

After communication has been established, the externally supplied module
is independent of the power on/off state of the standard device.

Protection against uncontrolled start−up

After a fault (e.g. short−term mains failure), a restart of the drive is not always
wanted and − in some cases − even not allowed.
The restart behaviour of the controller can be set in C0142:

ƒ

C0142 = 0 (Lenze setting)
– The controller remains inhibited (even if the fault is no longer active).
– The drive starts in a controlled mode by explicitly enabling the controller:

LOW−HIGH edge at terminal 28 (CINH)

ƒ

C0142 = 1
– An uncontrolled restart of the drive is possible.

«
...
30
31
32
33
34
...
»

Содержание E82ZAFIC010








































































Отзывы:

Нет отзывов