Lenze AC Tech ESVZAP0 Скачать руководство пользователя страница 19 | Manualshive

Страница: 19 / 49

background image

13

CMVPFB01A

Cyclic Data Access

5.

Cyclic Data Access

5.1 What is Cyclic Data?

Cyclic / Process / Polled data is the name given to the method used to transfer routine process data
between the network master and slave nodes.

Cyclic data transfer must be configured during network setup.

The terms “OUT data” and “IN data” describe the direction of data transfer as seen by the PROFIBUS-
DP network master controller.

The cyclic data source and destinations are configured and controlled by the SMV PROFIBUS-DP
modules mapping capabilities.

5.2 Mapping Cyclic Data

5.2.1 Data OUT (Dout) Channels

P440 to P445 - Dout Mapping Channels

Default: various

Range: 0 - 9

Access: RW

Type: Integer

The SMV PROFIBUS-DP module has 6 cyclic OUT channels each of which utilises 1 WORD of data.
Table 7 lists the mapping destinations for OUT going data being sent from the network master.
Last mapping channel not equal to 0 sets the size of Dout data portion.

Table 7 – Data OUT (Dout) Mappings

Parameter

Function

Default

Selection

P440

Dout Channel 0 mapping

1

0 – Disabled

1 – SMV Control Word

2 – Network Command Frequency

3 – Lenze C135 Control Word

4 – Network Speed in unsigned RPMs

5 – Network PID Setpoint

6 – Network Torque Setpoint

7 – Network Speed in signed RPMs (control direction)

8 – Digital O Relay

9 – Analog Output

P441

Dout Channel 1 mapping

2

P442

Dout Channel 2 mapping

0

P443

Dout Channel 3 mapping

0

P444

Dout Channel 4 mapping

0

P445

Dout Channel 5 mapping

0

WARNING

Modification to the Dout configuration may result in changes to present controller state,
including starting.

•

•

•

•

•
•
•

«
...
17
18
19
20
21
...
»

Содержание ESVZAP0


















































Отзывы:

Нет отзывов

Похожие инструкции для ESVZAP0

Бренд: K'Nex Education Страницы: 56

Бренд: Watts Страницы: 12

Бренд: Lancom Страницы: 8

Бренд: Valcom Страницы: 3

Бренд: Valcom Страницы: 3

Бренд: Valcom Страницы: 2

Бренд: Balboa Страницы: 74

Бренд: Cadac Страницы: 4

Бренд: CAME Страницы: 2

Бренд: FEAS Страницы: 4

Бренд: Danfoss Страницы: 2

Бренд: Conductrix Wampfler Страницы: 23

Бренд: Carel Страницы: 2

Бренд: Timotion Страницы: 9

Controller CR100

Бренд: Sonos Страницы: 2

Level-Trac LT-310

Бренд: QTS Страницы: 12

Бренд: Nordson Страницы: 20

MOVIFIT SC series

Бренд: SEW Страницы: 148

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды