Lenovo x3650 M5 Скачать руководство пользователя страница 158

Страница: 158 / 1340

SAS signal cable
(Y cable)

Power / configuration
cables

SAS 0 SAS 1

Figure 72. 24x2.5-inch hot-swap hard disk drive cabling

3.5-inch hard disk drive cable connection

The following illustrations show the cabling information for the 3.5-inch drive models.

Important:

Make sure all SAS cables are routed lower than the DIMM latches.

8x3.5-inch drive model

The internal routing for the 8x3.5-inch drive model cables.

The following illustration shows the internal routing for the 8x3.5-inch drive model cables.

Note:

There might be 3 or 4 power connectors on the system board depending on your configuration.

However, this difference will not affect the cable routing. Follow the following illustrations to complete
your cable routing.

146

Lenovo System x3650 M5 Installation and Service Guide

Содержание x3650 M5





























































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание x3650 M5

Отзывы:

Похожие инструкции для x3650 M5

Бренды по названию

Популярные бренды

Lenovo x3650 M5, Инструкция по установке и обслуживанию

Результаты поиска

Содержание x3650 M5

Отзывы:

Похожие инструкции для x3650 M5

Бренды по названию

Популярные бренды