Lenovo x3650 M4 BD 5466 Скачать руководство пользователя страница 41

Страница: 41 / 1222

System
management
(dedicated)

Video
connector

Serial
connector

USB 3 - 6
connectors

Ethernet 2
connector

Ethernet 1 connector
System management (shared)

Ethernet 4
connector

Ethernet 3
connector

Figure 16. System-board external connectors

System-board switches, jumpers, and buttons

The following illustration shows the location of the switches, jumpers, and buttons on the server.

Note:

If there is a clear protective sticker on the top of the switch blocks, you must remove and discard it

to access the switches.

Chapter 2

Installing optional devices

Содержание x3650 M4 BD 5466







































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание x3650 M4 BD 5466

Отзывы:

Похожие инструкции для x3650 M4 BD 5466

Бренды по названию

Популярные бренды

Lenovo x3650 M4 BD 5466, Инструкция по установке и обслуживанию

Результаты поиска

Содержание x3650 M4 BD 5466

Отзывы:

Похожие инструкции для x3650 M4 BD 5466

Бренды по названию

Популярные бренды