Lenovo x3650 M4 BD 5466 Скачать руководство пользователя страница 275

Страница: 275 / 1222

The following illustration shows cable routing for the DVD cable:

Attention:

Follow the optical drive cable routing as the illustration shows. Make sure that the

cable is not pinched and does not cover any connectors or obstruct any components on the
system board.

Optical drive
connector

Release tab

DVD drive
cable

Cable connector
latch

Figure 179. DVD drive cable routing

Step 6.

Replace the air baffle (see “Replacing the air baffle” on page 242).

Step 7.

Replace the cover (see “Replacing the cover” on page 240).

Step 8.

Slide the server into the rack.

Step 9.

Reconnect the power cords and any cables that you removed.

Step 10. Turn on the peripheral devices and the server.

Removing a tape drive

Use this information to remove a tape drive.

To remove an optional tape drive, complete the following steps:

Chapter 6

Removing and replacing components

263

Содержание x3650 M4 BD 5466







































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание x3650 M4 BD 5466

Отзывы:

Похожие инструкции для x3650 M4 BD 5466

Бренды по названию

Популярные бренды

Lenovo x3650 M4 BD 5466, Инструкция по установке и обслуживанию

Результаты поиска

Содержание x3650 M4 BD 5466

Отзывы:

Похожие инструкции для x3650 M4 BD 5466

Бренды по названию

Популярные бренды