Lenovo x3650 M4 BD 5466 Скачать руководство пользователя страница 247

Страница: 247 / 1222

Video graphic
adapters

VGA power
connector 2

VGA power
connector 1

VGA power
cables

Figure 151. VGA power cables connection

2.5-inch hard disk drive cable connection

8-drive-capable model

The following illustrations show the cabling information for the model of 8x2.5-inch hot-swap drive bays.

The following illustration shows the cabling information for the configuration cable in the server:

Configuration cable

Chapter 6

Removing and replacing components

235

Содержание x3650 M4 BD 5466







































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание x3650 M4 BD 5466

Отзывы:

Похожие инструкции для x3650 M4 BD 5466

Бренды по названию

Популярные бренды

Lenovo x3650 M4 BD 5466, Инструкция по установке и обслуживанию

Результаты поиска

Содержание x3650 M4 BD 5466

Отзывы:

Похожие инструкции для x3650 M4 BD 5466

Бренды по названию

Популярные бренды