Lenovo x3650 M4 BD 5466 Скачать руководство пользователя страница 186

Страница: 186 / 1222

Figure 142. System board error LEDs

Light path diagnostics LEDs

This section describes the LEDs on the light path diagnostics panel and suggested actions to correct
the detected problems.

For additional information, see “Server controls, LEDs, and power” on page 16 and “System-board LEDs” on
page 31 for the location of the system board LEDs.

174

Lenovo System x3650 M4 Installation and Service Guide

Содержание x3650 M4 BD 5466







































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание x3650 M4 BD 5466

Отзывы:

Похожие инструкции для x3650 M4 BD 5466

Бренды по названию

Популярные бренды

Lenovo x3650 M4 BD 5466, Инструкция по установке и обслуживанию

Результаты поиска

Содержание x3650 M4 BD 5466

Отзывы:

Похожие инструкции для x3650 M4 BD 5466

Бренды по названию

Популярные бренды