Lenovo x3250 m6 Скачать руководство пользователя страница 90 | Manualshive

Страница: 90 / 696

background image

Out-of-band method

See the IMM2 documentation (

Integrated Management Module II User's Guide

) at

http://publib.boulder.ibm.com/infocenter/systemx/documentation/topic/com.lenovo.sysx.imm2.doc/
product_page.html.

Automated boot recovery (ABR)

While the server is starting, if the integrated management module II detects problems with the server
firmware in the primary bank, the server automatically switches to the backup firmware bank and gives
you the opportunity to recover the firmware in the primary bank. For instructions for recovering the UEFI
firmware, see “Recovering the server firmware (UEFI update failure)” on page 74. After you have recovered
the firmware in the primary bank, do the following:

Step 1.

Restart the server.

Step 2.

When the prompt

Press F3 to restore to primary

is displayed, press F3 to start the server from

the primary bank.

Nx-boot failure

Configuration changes, such as added devices or adapter firmware updates, and firmware or application
code problems can cause the server to fail POST (the power-on self-test). If this occurs, the server responds
in either of the following ways:

• The server restarts automatically and attempts POST again.

• The server hangs, and you must manually restart the server for the server to attempt POST again.

After a specified number of consecutive attempts (automatic or manual), the Nx-boot failure feature causes
the server to revert to the default UEFI configuration and start the Setup Utility so that you can make the
necessary corrections to the configuration and restart the server. If the server is unable to complete POST
with the default configuration successfully, there might be a problem with the system board.

You can set the number of consecutive restart attempts that will trigger the Nx-boot failure feature, in
the Setup Utility. To specify the number, click

System Settings

➙

Recovery

➙

POST Attempts

➙

POST Attempts Limit

. Then, choose the item from the following available options:

3

,

6

,

9

, and

Disable

Nx-boot failure

.

76

Lenovo System x3250 M6 Installation and Service Guide

«
...
88
89
90
91
92
...
»

Содержание x3250 m6

























































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для x3250 m6

Express5800/T110g-E

Бренд: NEC Страницы: 2

Бренд: Panasonic Страницы: 28

LUXOMAT net ViSTATION

Бренд: B.E.G. Страницы: 4

Modbus Server-Cerberus ISO1745

Бренд: IntesisBox Страницы: 5

Бренд: TYAN Страницы: 81

Бренд: ASROCK Страницы: 40

Бренд: Acnodes Страницы: 1

Бренд: Acksys Страницы: 24

Бренд: McIntosh Страницы: 12

Бренд: McIntosh Страницы: 52

Бренд: Bosanova Страницы: 2

Бренд: Bosanova Страницы: 2

Бренд: Bosanova Страницы: 2

Бренд: eNet Страницы: 7

Бренд: DM&P Group Страницы: 27

Бренд: Meinberg Страницы: 55

Бренд: Supero Страницы: 108

Бренд: Supero Страницы: 114

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды