Lenovo x3250 m6 Скачать руководство пользователя страница 36

Страница: 36 / 696

Figure 10. Connectors on the system board

PCI riser card connector

Microprocessor power connector

Power supply connector

Backplane power connector

DIMM slot 1

DIMM slot 2

DIMM slot 3

DIMM slot 4

Power distribution board connector

System fan 1 connector

System fan 2 connector

System fan 3 connector

System fan 4 connector

Mini-SAS connector

SATA optical drive connector

Operation information panel connector

Coin-cell battery connector

Front USB connector

USB hypervisor key connector

Operating temperature enhancement kit connector

System-board switches and jumpers

This topic helps you locate the jumpers and switches on the system board and get familiar with their
functions.

Important:

• Before you change any switch settings or move any jumpers, turn off the server. Then, disconnect all

power cords and external cables. Review the information in “Safety” on page v, “Before removing or
installing server components” on page 87, and “Turning off the server” on page 13.

• Any system-board switch or jumper block that is not shown in the illustrations in this document are

reserved.

• If there is a clear protective sticker on the switch blocks, you must remove and discard it to access

the switches.

Lenovo System x3250 M6 Installation and Service Guide

Содержание x3250 m6

























































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание x3250 m6

Отзывы:

Похожие инструкции для x3250 m6

Бренды по названию

Популярные бренды

Lenovo x3250 m6, Инструкция по установке и обслуживанию

Результаты поиска

Содержание x3250 m6

Отзывы:

Похожие инструкции для x3250 m6

Бренды по названию

Популярные бренды