manualshive.com logo in svg

Lenovo tihnkserver rd330, Руководство по техническому обслуживанию аппаратной части

Поделиться
Скачать
Lenovo tihnkserver rd330 Скачать руководство пользователя страница 90

2. If the server is installed in a rack cabinet, remove the server from the rack cabinet and place it on a flat,

clean, and static-protective surface. See the

Rack Installation Instructions

that comes with the server.

3. Remove the server cover. See “Removing the server cover” on page 71.

4. Insert a finger into each of the two holes in the cooling shroud, and then lift the cooling shroud out of

the server.

PSU

Mem

CPU

ID

Figure 31. Removing the cooling shroud

Attention:

For proper cooling and airflow, reinstall the cooling shroud before turning on the server. Operating

the server for more than 30 minutes with the cooling shroud removed might damage server components.

Reinstalling the cooling shroud

Attention:

Do not open your server or attempt any repair before reading and understanding “Safety information”

on page iii and “Guidelines” on page 69.

This topic provides instructions on how to reinstall the cooling shroud.

Before you begin, print all the related instructions or ensure that you can view the PDF version on another
computer for reference.

Note:

Depending on the model, your server might look slightly different from the illustrations in this topic.

To reinstall the cooling shroud, do the following:

1. Ensure that all components have been reassembled correctly and that no tools or loose screws are

left inside your server.

2. Ensure that all cables inside the server have been properly routed so that they will not interfere with

installing the cooling shroud.

76

ThinkServer RD330 Hardware Maintenance Manual

Содержание tihnkserver rd330







































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды