manualshive.com logo in svg

Lenovo tihnkserver rd330, Руководство по техническому обслуживанию аппаратной части

Поделиться
Скачать
Lenovo tihnkserver rd330 Скачать руководство пользователя страница 44

The following illustrations show the connectors on the backplane for 3.5-inch hard disk drives.

Figure 17. Front view of the backplane for 3.5-inch hard disk drives

1

Slot 0 for a 3.5-inch hard disk drive

3

Slot 2 for a 3.5-inch hard disk drive

2

Slot 1 for a 3.5-inch hard disk drive

4

Slot 3 for a 3.5-inch hard disk drive

Figure 18. Rear view of the backplane for 3.5-inch hard disk drives

1

8-pin power connector

3

Mini-SAS ports 0-3

2

Optical drive power connector

1

8-pin power connector

Used to connect a power cable to provide power to the backplane.

2

Optical drive power connector

Used to connect the power cable for the slim optical drive if the server has one installed.

3

Mini-SAS ports 0-3

Used to connect the mini-SAS connector on one end of a mini-SAS to mini-SAS signal cable to support the
hard disk drive 0 to hard disk drive 3.

Backplane for 2.5-inch hard disk drives

This topic provides information to help you locate the connectors on the backplane for 2.5-inch hard disk
drives.

30

ThinkServer RD330 Hardware Maintenance Manual

Содержание tihnkserver rd330







































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды