manualshive.com logo in svg

Lenovo tihnkserver rd330, Руководство по техническому обслуживанию аппаратной части

Поделиться
Скачать
Lenovo tihnkserver rd330 Скачать руководство пользователя страница 28

The machine type, model, and serial number label is attached on the pull-out information card, which is a
small plastic tab and can be slid out of the front of the chassis. The following illustrations are samples of the
machine type, model, and serial number labels on server models with different hard disk drive configurations.

Note:

Depending on the model, your server might look slightly different from the illustrations in this topic.

ID

CPU

Mem

PSU

MT-M XXXX- XXX
S/N XXXXXXX

Figure 2. Label on server models with 3.5-inch hard disk drives

PSU

Mem

CPU

ID

MT-M XXXX- XXX
S/N XXXXXXX

Figure 3. Label on server models with 2.5-inch hard disk drives

Front view of the server

This topic provides information to help you locate the parts on the front of the server.

The front view of the server varies by model. The illustrations in this topic show the server front views
based on the supported hard disk drives:

• Front view of server models with 3.5-inch hard disk drives

14

ThinkServer RD330 Hardware Maintenance Manual

Содержание tihnkserver rd330







































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды