Lenovo tihnkserver rd330 Скачать руководство пользователя страница 174 | Manualshive

Страница: 174 / 198

Lenovo tihnkserver rd330 Скачать руководство пользователя страница 174

7. Reconnect external cables and power cords to the server. See “Rear view of the server” on page 21 to

identify the connectors on the rear panel of the server.

Attention:

To avoid component damage, connect the power cords last.

Note:

In most areas of the world, Lenovo requires the return of the defective CRU. Information about this will

come with the CRU or will come a few days after the CRU arrives.

Updating the server configuration

When you turn on the server for the first time after you install, remove, or replace a device, you might
need to update the server configuration.

Some optional devices have device drivers that you must install. For information about installing device
drivers, use the documentation that comes with each optional device. To obtain the supported device
drivers for your server from the Lenovo Support Web site, go to http://www.lenovo.com/drivers and follow
the instructions on the Web page to find and download the device drivers you need.

Refer to the following information resources to update the server configuration:

• To update the BIOS configuration, see “Using the Setup Utility program” on page 47.

• To update the RAID configuration, see “Configuring RAID” on page 58.

• To use the ThinkServer EasyStartup program, see “Using the ThinkServer EasyStartup program” on

• To update your system firmware, see “Updating the firmware” on page 67.

160

ThinkServer RD330 Hardware Maintenance Manual

«
...
172
173
174
175
176
...
»

Содержание tihnkserver rd330







































































































































































































Отзывы:

Нет отзывов

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды