Lenovo tihnkserver rd330 Скачать руководство пользователя страница 170 | Manualshive

Страница: 170 / 198

Lenovo tihnkserver rd330 Скачать руководство пользователя страница 170

Reinstalling the server cover and reconnecting cables

Attention:

Do not open your server or attempt any repair before reading and understanding “Safety information”

on page iii and “Guidelines” on page 69.

This topic provides instructions on how to reinstall the server cover and reconnect cables to your server.

Attention:

For proper cooling and airflow, reinstall the server cover before turning on the server. Operating

the server for extended periods of time (more than 30 minutes) with the server cover removed might
damage server components.

Before you begin, print all the related instructions or ensure that you can view the PDF version on another
computer for reference.

Note:

Depending on the model, your server might look slightly different from the illustrations in this topic.

To reinstall the server cover and reconnect cables to your server, do the following:

1. Ensure that all components have been reassembled correctly and that no tools or loose screws are

left inside your server.

2. Ensure that all internal cables are routed correctly and secured by any cable clips or ties in the server.

Keep cables clear of the hinges and sides of the server chassis to avoid interference with reinstalling
the cooling shroud and the server cover. The following illustrations show the cable routing for the two
chassis configurations based on the supported hard disk drives.

156

ThinkServer RD330 Hardware Maintenance Manual

«
...
168
169
170
171
172
...
»

Содержание tihnkserver rd330







































































































































































































Отзывы:

Нет отзывов

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды