manualshive.com logo in svg

Lenovo tihnkserver rd330, Руководство по техническому обслуживанию аппаратной части

Поделиться
Скачать
Lenovo tihnkserver rd330 Скачать руководство пользователя страница 122

5. Remove the TPM from the TPM connector by lifting it straight up.

Note:

Carefully handle the TPM by its edges.

Figure 56. Removing the TPM

6. If you have lifted the riser card assembly 1, reinstall it into the chassis. See “Replacing the riser card

assembly 1” on page 145.

7. If you are instructed to return the old TPM, follow all packaging instructions and use any packaging

materials that are supplied to you for shipping.

What to do next:

• To work with another piece of hardware, go to the appropriate section.

• To complete the removal procedure, go to “Completing the parts replacement” on page 155.

Installing or replacing a hot-swap redundant power supply

This topic provides instructions on how to install or replace a hot-swap redundant power supply.

On each hot-swap redundant power supply, there is a status LED near the power cord connector. When the
LED is lit in green, it indicates that the hot-swap redundant power supply is working correctly. When the LED
is lit in amber, it indicates that the hot-swap redundant power supply is likely to fail or has failed.

108

ThinkServer RD330 Hardware Maintenance Manual

Содержание tihnkserver rd330







































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды