Lenovo ThinkSystem ST550 Скачать руководство пользователя страница 108

Страница: 108 / 136

Install the foot stands

Use this information to install the foot stands.

To install the foot stands, complete the following steps:

Watch the procedure

. A video of the installation process is available:

• Youtube:

https://www.youtube.com/playlist?list=PLYV5R7hVcs-Acsjj4tU79GzKnWG316BYn

• Youku:

http://list.youku.com/albumlist/show/id_50483452

Step 1. Lay the server on its side for easier operation.

Step 2. For each foot stand, carefully insert the two tabs on the foot stand into the corresponding holes in

the chassis. Then, pivot the foot stand inward until the other side clicks into place.

Figure 66. Foot stand installation

Important:

To help the server stand steadily, ensure that the foot stands are installed outward as

shown in “Front view” on page 15.

Install a simple-swap drive

Use this information to install a simple-swap drive.

Static Sensitive Device

Ground package before opening”

on page 59

The following notes describe the type of drives that your server supports and other information that you must
consider when you install a drive.

• For a complete list of supported optional devices for the server, see:

http://www.lenovo.com/us/en/serverproven/

• The drive bays are numbered to indicate the installation order (starting from number “0”). Follow the

installation order when you install a drive. See “Front view” on page 15.

104

ThinkSystem ST550 Setup Guide

Содержание ThinkSystem ST550









































































































































Результаты поиска

Содержание ThinkSystem ST550

Отзывы:

Похожие инструкции для ThinkSystem ST550

Бренды по названию

Популярные бренды

Lenovo ThinkSystem ST550, Руководство по установке

Результаты поиска

Содержание ThinkSystem ST550

Отзывы:

Похожие инструкции для ThinkSystem ST550

Бренды по названию

Популярные бренды