Lenovo ThinkSystem SR550 Скачать руководство пользователя страница 68

Страница: 68 / 206

CAUTION:
Hazardous moving fan blades nearby. Keep fingers and other body parts away.

Remove the air baffle

Use this information to remove the air baffle.

Before removing the air baffle:

1. Remove the top cover. See “Remove the top cover” on page 56.
2. If there is a RAID super capacitor module installed on the top of the air baffle, remove the RAID super

capacitor module first.

To remove the air baffle, complete the following step:

Watch the procedure

A video of this procedure is available at

https://www.youtube.com/playlist?list=PLYV5R7hVcs-

C9jFjZnXQ6AmTXaIdX6_HJ

Figure 31. Air baffle removal

Step 1. Grasp the air baffle and carefully lift it out of the server.

ThinkSystem SR550 Maintenance Manual

Содержание ThinkSystem SR550















































































































































































































Результаты поиска

Содержание ThinkSystem SR550

Отзывы:

Похожие инструкции для ThinkSystem SR550

Бренды по названию

Популярные бренды

Lenovo ThinkSystem SR550, Руководство по обслуживанию

Результаты поиска

Содержание ThinkSystem SR550

Отзывы:

Похожие инструкции для ThinkSystem SR550

Бренды по названию

Популярные бренды