Lenovo ThinkStation P500 Скачать руководство пользователя страница 44 | Manualshive

Страница: 44 / 232

Lenovo ThinkStation P500 Скачать руководство пользователя страница 44

Locating internal drives

Internal drives are devices that your computer uses to read and store data. You can add drives to your
computer to increase storage capacity and enable your computer to read other types of media. Internal
drives are installed in bays.

When you install or replace an internal drive, note the type and size of the drive that each bay supports and
correctly connect the required cables. Refer to the appropriate section in “Installing or replacing hardware”
on page 111 for instructions on how to install or replace internal drives for your computer.

The following illustration shows the locations of the drive bays.

Figure 8. Drive bay locations

1

Card reader (for an SD card)

2

Optical drive bays (2) (for an optical drive, a flex module, or a front-access storage enclosure)

3

Storage drive bays (4) (for a hard disk drive, a hybrid drive, or a solid-state drive)

38

ThinkStation P500 and P700 Hardware Maintenance Manual

«
...
42
43
44
45
46
...
»

Содержание ThinkStation P500









































































































































































































































Отзывы:

Нет отзывов