Lenovo ThinkStation P500 Скачать руководство пользователя страница 203

Страница: 203 / 232

2. Unscrew the Wi-Fi antenna cable from the rear of the computer.

Figure 147. Removing the rear Wi-Fi antenna

What to do next:

• To work with another piece of hardware, go to the appropriate section.

• To complete the installation or replacement, go to “Completing the parts replacement” on page 198.

Replacing the keyboard or mouse

Attention:

Do not open your computer or attempt any repair before reading and understanding the Chapter

1 “Read this first: Important safety information” on page 1.

Note:

The keyboard and mouse are available only on some models.

To replace the keyboard or mouse, do the following:

1. Disconnect the old keyboard cable or mouse cable from the computer.

Chapter 11

Installing or replacing hardware

197

Содержание ThinkStation P500









































































































































































































































Результаты поиска

Содержание ThinkStation P500

Отзывы:

Lenovo ThinkStation P500, Руководство по техническому обслуживанию аппаратной части, Страница: 203 / 232

Результаты поиска

Содержание ThinkStation P500

Отзывы: