Lenovo ThinkServer TS130 1098 Скачать руководство пользователя страница 88 | Manualshive

Страница: 88 / 130

background image

Table 25. Items under the

Startup

menu (continued)

Item

Option

Description

Keyboardless Operation

Enabled / [Disabled]

Enable or disable the keyboardless
operation. This function enables
the system to function without a
keyboard. It is commonly used when
the system has been set up as a
network server.

Note:

If it is enabled, systems without

keyboards will not display keyboard
errors during the POST.

Option Keys Display

[Enabled] / Disabled

Enable or disable the Option Keys
Display function. When this function
is enabled, the system software
option key (such as the F1 key)
prompts will be displayed.

Note:

Disabling the prompts will not

affect the function of a specific key.

Option Keys Display Style

[Normal] / Legacy

Control the prompts displayed on the
POST logo screen.

•

Normal

: During the POST, this

message will be displayed:

To

interrupt normal startup, press
Enter

.

•

Legacy

: During the POST, this

message will be displayed:

Press

F1 to enter Setup and press F12 to
display Boot Menu

.

Startup Device Menu Prompt

[Enabled] / Disabled

Enable or disable the Startup Device
Menu Prompt. This function enables
the Startup Device Menu to be
displayed by pressing F12 after the
server is turned on. The Startup
Device Menu enables the sequence
of startup devices to be temporarily
changed.

Note:

[ ] indicates the default setting.

Table 26. Items under the

Exit

menu

Item

Description

Save Changes and Exit

Exit the Setup Utility program after saving the changes.

Discard Changes and Exit

Exit the Setup Utility program without saving any changes.

Load Optimal Defaults

Restore/Load default values for all the setup options.

Viewing and changing settings

The Setup Utility program menu lists various items about the system configuration. To view or change
settings, start the Setup Utility program. See “Starting the Setup Utility program” on page 63. Then, follow
the instructions on the screen.

You can use either the keyboard or the mouse to navigate through BIOS menu choices. The keys used to
perform various tasks are displayed at the bottom of each screen.

76

ThinkServer TS130 Hardware Maintenance Manual

«
...
86
87
88
89
90
...
»

Содержание ThinkServer TS130 1098



































































































































Отзывы:

Нет отзывов

Похожие инструкции для ThinkServer TS130 1098

Бренд: A10 Networks Страницы: 17

Univerge SV9100

Бренд: NEC Страницы: 78

UNIVERGE SL2100

Бренд: NEC Страницы: 34

Бренд: NEC Страницы: 2

Бренд: NEC Страницы: 975

Sun Fire X2100 M2

Бренд: Sun Microsystems Страницы: 128

NPort W2150Plus Series

Бренд: Moxa Technologies Страницы: 167

Бренд: LevelOne Страницы: 88

Бренд: Vxl Страницы: 2

SuperServer 7089P-TR4T

Бренд: Supermicro Страницы: 155

Express5800/R320f-E4

Бренд: NEC Страницы: 88

Бренд: Cavalry Страницы: 16

Express5800/E120d-1

Бренд: NEC Страницы: 4

Express5800/B140a-T

Бренд: NEC Страницы: 19

Express5800/B120f-h

Бренд: NEC Страницы: 21

Express5800/GT110b

Бренд: NEC Страницы: 27

Express5800/GT110e-S

Бренд: NEC Страницы: 34

Express5800/B110d

Бренд: NEC Страницы: 19

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды