Lenovo ThinkServer RD350G Скачать руководство пользователя страница 34

Страница: 34 / 186

System health LED

The system health LED helps you to determine if there are any system errors.

•

Off

: The server is off or the server is on and working correctly.

•

Amber

: The server has potential system errors. Check the information in the following table for potential

system errors and corresponding solutions.

•

Blinking

: TSM initialization is in progress.

Potential system error (system health LED: amber)

Solution

The temperature of the server reached the non-critical
temperature threshold.

Check the BMC for errors and check the system fans.

The voltage of the server reached the non-critical voltage
threshold.

Replace the system board.

Note:

This action must be performed only by Lenovo

service personnel. See

Chapter 8 “Getting information,

help, and service” on page 151.

A fan is running at low speed.

Check the system fans.

A system fan has been removed.

1. Ensure that the system fans are connected securely

to the system board.

2. Reinstall the removed fan or install a new fan to

replace the removed fan.

The power supply has a critical error.

Check the BMC for detailed information.

A power cord has been disconnected or a redundant
power supply has been removed.

1. Ensure that the power supplies are installed securely.

2. Ensure that the power cords are connected securely

to the power supplies.

3. Install a new power supply to replace the removed

one.

The system is overheated.

Check the BMC for errors and then check the system
fans.

Power button with power status LED

You can press the power switch to turn on the server when you finish setting up the server. You also can
hold the power switch for several seconds to turn off the server if you cannot turn it off from the operating
system. See Chapter 4

“Turning on and turning off the server” on page 41. The power status LED helps you

to determine the current power status.

Status

Color

Description

Green

The server is on.

Off

None

The server is off.

ThinkServer RD350G User Guide and Hardware Maintenance Manual

Содержание ThinkServer RD350G



























































































































































































Результаты поиска

Содержание ThinkServer RD350G

Отзывы:

Похожие инструкции для ThinkServer RD350G

Бренды по названию

Популярные бренды

Lenovo ThinkServer RD350G, Руководство пользователя и руководство по техническому обслуживанию аппаратного обеспечения

Результаты поиска

Содержание ThinkServer RD350G

Отзывы:

Похожие инструкции для ThinkServer RD350G

Бренды по названию

Популярные бренды