Lenovo ThinkServer RD350G Скачать руководство пользователя страница 151

Страница: 151 / 186

5. Remove the old coin-cell battery.

Figure 114. Removing the coin-cell battery

6. Install a new coin-cell battery.

Figure 115. Installing the coin-cell battery

7. If you have lifted up the riser card assembly, reinstall it into the chassis. See

“Replacing the riser

card assembly” on page 133.

8. Dispose of the old coin-cell battery as required by local ordinances or regulations.

What to do next:

• To work with another piece of hardware, go to the appropriate section.
• To complete the replacement, go to “Completing the parts replacement” on page 142.

Note:

After you replace the system board battery, you must reset passwords, reset system date and time,

and reconfigure the server. See

Chapter 5 “Configuring the server” on page 43.

For service technician only: replacing the system board

CAUTION:

Hazardous moving parts. Keep fingers and other body parts away.

Chapter 6

Replacing hardware

137

per

only

vice personnel enovo.

your

eading and

page and

page

Содержание ThinkServer RD350G



























































































































































































Результаты поиска

Содержание ThinkServer RD350G

Отзывы:

Бренды по названию

Популярные бренды

Lenovo ThinkServer RD350G, Руководство пользователя и руководство по техническому обслуживанию аппаратного обеспечения

Результаты поиска

Содержание ThinkServer RD350G

Отзывы:

Бренды по названию

Популярные бренды