Lenovo ThinkCentre M800 Скачать руководство пользователя

Страница: 44 / 178

PCI Express x1 card slot

PCI Express x16 card slot

Rear fan connector

Cover presence switch connector (intrusion switch

connector)

Coin-cell battery

Machine type and model label

The machine type and model label identifies your computer. When you contact Lenovo for help, the machine
type and model information helps support technicians to identify your computer and provide faster service.

The machine type and model label is attached on the side of your computer as shown.

Figure 6. Machine type and model label

Features

The computer features introduced in this section apply to various models.

Information about your computer

• To view basic information (such as microprocessor and memory information) about your computer,

do the following:

1. Click the Start button to open the Start menu.

2. Depending on your Windows version, do one of the following:

– For Windows 7: Right-click

Computer

, and then click

Properties

– For Windows 10: Click

Settings

➙

System

➙

About

• To view detailed information about the devices (such as the optical drive and network adapters) on your

computer, do the following:

1. Depending on your Windows version, do one of the following:

ThinkCentre M800 and M900 Hardware Maintenance Manual

Содержание ThinkCentre M800


















































































































































































Результаты поиска

Содержание ThinkCentre M800

Отзывы:

Похожие инструкции для ThinkCentre M800

Бренды по названию

Популярные бренды

Lenovo ThinkCentre M800, Руководство по техническому обслуживанию аппаратной части

Результаты поиска

Содержание ThinkCentre M800

Отзывы:

Похожие инструкции для ThinkCentre M800

Бренды по названию

Популярные бренды