manualshive.com logo in svg

Lenovo ThinkCentre M800, Руководство по техническому обслуживанию аппаратной части, Страница: 37 / 178

Поделиться
Скачать
Lenovo ThinkCentre M800 Скачать руководство пользователя страница 37

Rear view

Figure 2. Rear view

1

Power cord connector

2

Serial connector

3

VGA connector

4

DisplayPort

®

connectors (2)

5

USB 3.0 connectors (4)

6

USB 2.0 connectors (2) (for M800 models) or USB 3.0

connectors (2) (for M900 models)

7

Microphone connector

8

Audio line-out connector

9

Audio line-in connector

10

PCI/PCI-Express card area (different cards provide

different connectors)

11

Ethernet connector

12

PS/2 keyboard and mouse connectors (some models)

13

Security-lock slot

14

Padlock loop

Note:

A discrete graphics card, network interface card, or audio card might be installed in the Peripheral

Component Interconnect (PCI) or PCI Express card area. If such a card is installed, ensure that you use the
connectors on the card instead of the corresponding connectors on the computer.

•

Audio line-in connector

Used to receive audio signals from an external audio device, such as a stereo system. When you attach
an external audio device, a cable is connected between the audio line-out connector of the device
and the audio line-in connector of the computer.

Chapter 2

.

Product overview

29

Содержание ThinkCentre M800



















































































































































































Отзывы:

Нет отзывов