Lenovo ThinkAgile VX 4-Socket 4U Certified Node Скачать руководство пользователя страница 58

Страница: 58 / 296

Figure 34. Cable routing, SAS drive cables (lower tray)

Table 27. Cable routing, SAS drive cables (lower tray)

Cable

Routing

PCIe SAS interface

•

From:

Lower system board in lower compute tray, “PCIe/NVMe” connector (see

“System-board connectors” on page 32)

•

To:

Storage interposer, connector “PCIe” (see “Storage interposer connectors” on

page 38)

RAID interface for drive

backplane 1

•

From:

RAID card, “C3” connector (see “RAID card connectors” on page 38)

•

To:

Drive backplane, connector “SAS” (see “Drive backplane connectors” on page

39)

RAID interface for drive

backplane 2

•

From:

RAID card, “C2” connector (see “RAID card connectors” on page 38)

•

To:

Drive backplane, connector “SAS” (see “Drive backplane connectors” on page

39)

RAID interface for drive

backplane 3

•

From:

RAID card, “C1” connector (see “RAID card connectors” on page 38)

•

To:

Drive backplane, connector “SAS” (see “Drive backplane connectors” on page

39)

NVMe drive cables (lower tray)

User Guide for ThinkAgile VX7820 Appliance, ThinkAgile VX 4-Socket 4U Certified Node

Содержание ThinkAgile VX 4-Socket 4U Certified Node









































































































































































































































































































Результаты поиска

Содержание ThinkAgile VX 4-Socket 4U Certified Node

Отзывы:

Lenovo ThinkAgile VX 4-Socket 4U Certified Node, Руководство пользователя, Страница: 58 / 296

Результаты поиска

Содержание ThinkAgile VX 4-Socket 4U Certified Node

Отзывы: