Lenovo ThinkAgile MX Certified Node 2U Скачать руководство пользователя страница 17

Страница: 17 / 104

Chapter 3. Server components

This section provides information to help you locate your server components.

Front view

The front view of the ThinkAgile MX Certified Nodes servers includes the drive LEDs and front I/O assembly.

The illustrations in this topic show the ThinkSystem SR650 server front views based on the supported drive
bays.

Notes:

• Your server might look different from the illustrations in this topic.

Figure 1. Front view of server models with twelve 3.5-inch drive bays (for ThinkAgile MX hybrid storage option)

Figure 2. Front view of server models with twenty-four 2.5-inch drive bays (for ThinkAgile MX all-flash option)

Table 2. Components on front of server

Callout

Pull-out information tab

Front I/O assembly

Rack latch (right)

Drive bays

Rack latch (left)

Drive activity LED

Содержание ThinkAgile MX Certified Node 2U









































































































Результаты поиска

Содержание ThinkAgile MX Certified Node 2U

Отзывы:

Похожие инструкции для ThinkAgile MX Certified Node 2U

Бренды по названию

Популярные бренды

Lenovo ThinkAgile MX Certified Node 2U, Руководство пользователя

Результаты поиска

Содержание ThinkAgile MX Certified Node 2U

Отзывы:

Похожие инструкции для ThinkAgile MX Certified Node 2U

Бренды по названию

Популярные бренды