Lenovo ThinkAgile CP 4000 Series Скачать руководство пользователя

Страница: 41 / 84

Install the compute slide rails

Procedures for installing ThinkAgile CP compute block slide rails in a rack.

The slide rails are extensible as shown in the following illustration:

Figure 17. Slide rails

To install the ThinkAgile CP compute block slide rails, do the following:

Step 1. Ensure that the slide rail is shortened to its shortest position.

Step 2. From the front of the rack cabinet, line up the pins on the rear of the slide rail with the flange holes

at the rear of the rack.

Step 3. Push the slide rail so that the pins and the latch snap into place.

Note:

The holes on the rack are either be square-shaped or round-shaped.

Figure 18. Left slide rear installation

Chapter 3

ThinkAgile CP Setup

Содержание ThinkAgile CP 4000 Series





















































































Результаты поиска

Содержание ThinkAgile CP 4000 Series

Отзывы:

Похожие инструкции для ThinkAgile CP 4000 Series

Бренды по названию

Популярные бренды

Lenovo ThinkAgile CP 4000 Series, Руководство по установке оборудования

Результаты поиска

Содержание ThinkAgile CP 4000 Series

Отзывы:

Похожие инструкции для ThinkAgile CP 4000 Series

Бренды по названию

Популярные бренды