Lenovo ThinkAgile CP 4000 Series Скачать руководство пользователя страница 33

Страница: 33 / 84

Install the storage slide rails into a round hole rack

Procedures for installing ThinkAgile CP storage block slide rails in a round hole rack.

To install the ThinkAgile CP storage block slide rails in a round hole rack, do the following:

Attention:

Ensure that you install the rear mounting rail brackets before installing the front mounting

brackets.

Figure 10. Installing the rail in a round hole rack

Step 1. Open the hinge bracket on the rear of the rail.

Step 2. Line up the pins on the rear of the rail with the corresponding holes in the rear-mounting flange of

the rack, and then insert the pins into the holes in the rack flange.

Step 3. Close the hinge bracket to secure the rail to the rack flange.

Step 4. Secure the rear mounting bracket of the rail with two M5 screws.

Chapter 3

ThinkAgile CP Setup

Содержание ThinkAgile CP 4000 Series





















































































Результаты поиска

Содержание ThinkAgile CP 4000 Series

Отзывы:

Похожие инструкции для ThinkAgile CP 4000 Series

Бренды по названию

Популярные бренды

Lenovo ThinkAgile CP 4000 Series, Руководство по установке оборудования

Результаты поиска

Содержание ThinkAgile CP 4000 Series

Отзывы:

Похожие инструкции для ThinkAgile CP 4000 Series

Бренды по названию

Популярные бренды