Lenovo System x3650 M4 HD Скачать руководство пользователя страница 44

Страница: 44 / 1168

System error
LED

Locator LED

Power LED

Dual-por t network
adapter LED

IMM hear tbeat
LED

RTMM hear tbeat LED

Standby power
LED

System battery
error LED

Fan 4
error LED

Fan 3
error LED

Microprocessor 2
error LED

Fan 2
error LED

Fan 1
error LED

Microprocessor 1
error LED

System board
error LED

DIMM 19-24
error LEDs
(under the latches)

DIMM 1-6
error LEDs
(under the latches)

DIMM 7-18
error LEDs
(under the latches)

Figure 17. System-board LEDs

System-board optional-device connectors

The following illustration shows the connectors on the system board for the optional devices.

Lenovo System x3650 M4 HD Installation and Service Guide

Содержание System x3650 M4 HD

















































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание System x3650 M4 HD

Отзывы:

Бренды по названию

Популярные бренды

Lenovo System x3650 M4 HD, Инструкция по установке и обслуживанию

Результаты поиска

Содержание System x3650 M4 HD

Отзывы:

Бренды по названию

Популярные бренды