manualshive.com logo in svg

Lenovo System x3650 M4 HD, Инструкция по установке и обслуживанию

Поделиться
Скачать
Lenovo System x3650 M4 HD Скачать руководство пользователя страница 42

CMOS clear
jumper (JP1)

UEFI boot backup
jumper (JP7)

System TPM physical
presence jumper (JP20)

Switch block 3 (SW3)

NMI button

1

2
3
4

off

on

1

2

3

1
2
3

1
2
3

Figure 16. System-board switches, jumpers, and buttons

The following table describes the jumpers on the system board.

Table 3. System board jumpers

Jumper number

Jumper name

Jumper setting

JP1

CMOS clear jumper

• Pins 1 and 2: Normal (default).

• Pins 2 and 3: Clears the real-time clock (RTC)

registry.

JP7

UEFI boot backup jumper

• Pins 1 and 2: Normal (default). Loads the

primary server firmware ROM page.

• Pins 2 and 3: Loads the secondary (backup)

server firmware ROM page.

JP20

System TPM physical presence
jumper

• Pins 1 and 2: Normal (default).

• Pins 2 and 3: Indicates a physical presence to

the system TPM.

1. If no jumper is present, the server responds as if the pins are set to the default.

2. Changing the position of the UEFI boot backup jumper (JP7) from pins 1 and 2 to pins 2 and 3 before the server

is turned on alters which flash ROM page is loaded. Do not change the jumper pin position after the server is
turned on. This can cause an unpredictable problem.

30

Lenovo System x3650 M4 HD Installation and Service Guide

Содержание System x3650 M4 HD

















































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды