Lenovo System x3650 M4 HD Скачать руководство пользователя страница 257

Страница: 257 / 1168

Fan-bracket
release latches

Figure 169. Fan bracket removal

Replacing the fan bracket

Use this information to replace the fan bracket.

To install the fan bracket, complete the following steps:

Step 1.

Read the safety information that begins on “Safety” on page v and “Installation guidelines”
on page 34.

Step 2.

Turn off the server and peripheral devices and disconnect all power cords.

Step 3.

Remove the cover (see “Removing the cover” on page 195).

Step 4.

Lower the fan bracket into the chassis.

Chapter 6

Removing and replacing components

245

Содержание System x3650 M4 HD

















































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание System x3650 M4 HD

Отзывы:

Бренды по названию

Популярные бренды

Lenovo System x3650 M4 HD, Инструкция по установке и обслуживанию

Результаты поиска

Содержание System x3650 M4 HD

Отзывы:

Бренды по названию

Популярные бренды