manualshive.com logo in svg

Lenovo System x3650 M4 HD, Инструкция по установке и обслуживанию

Поделиться
Скачать
Lenovo System x3650 M4 HD Скачать руководство пользователя страница 22

Approximate heat output:
• Minimum configuration: 419.68 Btu per hour (AC 123 watts)
• Maximum configuration: 4053 Btu per hour (AC 1188 watts)

Electrical input:

• Sine-wave input (50 - 60 Hz) required
• Input voltage low range:

– Minimum: 100 V ac
– Maximum: 127 V ac

• Input voltage high range:

– Minimum: 200 V ac
– Maximum: 240 V ac

• Input kilovolt-amperes (kVA), approximately:

– Minimum: 0.14 kVA
– Maximum: 1.201 kVA

Notes:

1. Power consumption and heat output vary depending on the number and type of optional features

installed and the power-management optional features in use.

2. The noise emission level stated is the declared (upper limit) sound power level, in bels, for a random

sample of machines. All measurements are made in accordance with ISO 7779 and reported in
conformance with ISO 9296. Actual sound-pressure levels in a given location might exceed the average
values stated because of room reflections and other nearby noise sources. The noise emission level
stated in the declared (upper limit) sound-power level, in bels, for a random sample of system.

Table 1. Power supply configurations

One or two

550-watt

power

supplies

One 750-watt power

supply

Two

750-watt

power

supplies

One 900-watt power

supply

Two

900-watt

power

supplies

Video
adapters

Not

supported

Not

supported

Quadro

K600 or

K2000

Two Quadro

K600 or

K2000

Not

supported

Quadro

K600 or

K2000

Two Quadro

K600 or

K2000

Microprocessor Support up

to 95-watt

Support up

to 115-watt

Maximum
amount of
DIMMs

8

(LRDIMM

not

supported)

16 for

UDIMM and

RDIMM

8 for

LRDIMM

16 for

UDIMM and

RDIMM

8 for

LRDIMM

16

(LRDIMM

not

supported)

24

(LRDIMM

not

supported)

24

(LRDIMM

not

supported)

Maximum
amount of PCI
adapters

2

1

1

1

3

1

2

Maximum
amount of
2.5-inch HDDs

16

26

26

26

26

26

16

Notes:

1. If you install two Quadro K600 or K2000 video adapters, you must install two power supplies (750-watt or

900-watt).

2. Power supplies in the server must be with the same power rating or wattage.

3. You may use the Power Configurator utility to determine current system power consumption. For more information

and to download the utility, go to http://www.ibm.com/systems/ bladecenter/resources/ powerconfig.html.

10

Lenovo System x3650 M4 HD Installation and Service Guide

Содержание System x3650 M4 HD

















































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды